Bathroom Tile Installation in Philadelphia, PA
Bathroom tile installation in Philadelphia comes down to the lines where everything meets: floor to tub, wall to floor, wet zone to dry. We tile floors, walls, tub surrounds, shower enclosures and niches, and each of those lines has to be watertight and straight. If you are gutting the room with new plumbing and cabinetry, we work alongside your general contractor.
Get my free estimateCall (267) 357-7482Bathroom Tile Installation, Wall to Floor to Transition
A bathroom is the hardest room in the house to tile well, and it is not because of the tile. It is because everything meets everything: the floor meets the tub, the wall meets the floor, the wet area meets the dry one, and each of those lines has to be both watertight and straight.
We do the tile part of your bathroom — floors, walls, tub surrounds, shower enclosures and niches. If you are gutting the room down to studs with new plumbing and cabinetry, you want a general contractor, and we work alongside one.
- Bathroom floors
- Wall tile and wainscot
- Tub surrounds
- Shower enclosures
- Custom niches
- Mosaic and accent details
Bathroom Tile Installation for Every Surface
Bathroom Floors
Slip-aware tile choice, flat substrate, transitions planned at the door.
Tub Surrounds
Waterproofed to the same standard as a shower, because it is the same water.
Wall Tile and Wainscot
Full-height or half-height, with the top edge finished in trim, not caulk.
Niches and Accents
Storage and focal points built into the layout instead of added to it.
Waterproofing the Wet Zone Before Bathroom Tile
A bathroom has two zones, and they are not treated the same. The shower and tub surround get a continuous waterproof membrane with sealed valves, niche edges and inside corners. The rest of the floor gets a flat, moisture-tolerant assembly and proper slope wherever there is a drain. Knowing where that line falls is most of the job.
Substrate inspection
What is behind the old tile, and whether it is dry.
Membrane in the wet zone
Continuous across the shower or tub walls and floor.
Sealed corners and penetrations
Valves, niche edges, inside corners.
Floor preparation
Flattening, and slope where there is a drain.
Tile, grout and final inspection
Set, grouted, silicone at movement joints, walked through with you.
Best Tile for a Bathroom Floor and Walls
Porcelain
Lowest water absorption. The safe default for bathroom floors.
Ceramic
Fine on walls, where it will not take traffic.
Natural Stone
Marble, slate, travertine. Needs sealing on a schedule; we tell you which one and how often.
Mosaic
More grout lines, more grip. Belongs on shower floors and small bathroom floors.
Our Bathroom Tile Process
Estimate
Measure, inspect the substrate, written number.
Preparation
Protect the room, remove old material, correct the surfaces.
Waterproof
Membrane in the wet zone, slope at the drain.
Install
Layout planned, tile set, joints consistent.
Inspect
Grout, silicone, clean and walkthrough.
Recent Bathroom Tile Projects in Philadelphia
What Affects Bathroom Tile Installation Cost?
For typical price ranges, read our bathroom tile installation cost guide for Philadelphia. For your own bathroom, send a photo and we put the number in writing.
A bathroom floor alone is one to two days. Floor plus tub surround runs three to five.
Room Size
Floor area plus wall area to be covered.
Wet Zone Extent
A tub surround is less than a full walk-in enclosure.
Tile Format
Mosaic and patterned tile take longer than straight-lay.
Substrate Condition
What is behind the old tile is the variable nobody budgets for.
Bathroom Tile Questions
How much does bathroom tile installation cost?
Floor area, wall area, tile format and the condition of the substrate. A floor-only job in porcelain is the low end; floor plus a full tiled enclosure in mosaic is the high end. We measure and give you a written number at no cost.
Do you do full bathroom remodels?
No — we install tile. Floors, walls, tub surrounds, shower enclosures and niches. Plumbing, fixtures, vanities and electrical are a general contractor work, and we regularly work alongside one. Telling you this up front saves both of us a wasted visit.
What tile is best for a bathroom floor?
Porcelain, because it absorbs almost no water. For grip, smaller tile with more grout lines beats a large polished slab — which is why mosaic and hexagon are so common on bathroom floors.
Do you waterproof behind a tub surround?
Yes. A tub surround takes the same water a shower does, and it gets the same membrane. Tile and grout alone do not stop water.
How long will my bathroom be out of use?
One to two days for a floor, three to five for floor plus surround, plus curing time before the shower is used. We give you the schedule with the estimate so you can plan around it.
Is it cheaper to tile a shower or use a surround?
A prefabricated acrylic or fiberglass surround usually costs less up front, because it goes in as a few large panels. Tile costs more in labor and waterproofing, but it can be laid out around niches, benches and any size of opening, and a damaged piece can be replaced on its own.
Bathroom Tile Installers Serving Philadelphia and South Jersey
Searching for bathroom tile installers in Philadelphia? Our crew is based in Northeast Philadelphia and works across the city, in nearby Pennsylvania towns and in South Jersey. A bathroom floor alone is usually one to two days, a floor plus tub surround runs three to five, and the schedule comes in writing with your free estimate.
Send a photo of the space. The estimate is free and comes in writing.
Get my free estimate
Free, no-obligation estimate
Get a Free Bathroom Tile Estimate
Photos and rough dimensions are enough to start. We answer every message.
Call (267) 357-7482
Mon–Fri 8:00am–5:00pm · Sat 9:00am–1:00pm